Fows Pumping

[fow1]

Okay Guys, here are some pics of me pumping. Please keep in mind I am a beginner(2days) so don’t be to critical. The first pic is just a straight tube. I am packing the tube because I don’t want any more girth. I still would like more length. Don’t know if you can tell, I have grad marks that indicate I am just slightly over 8" in the tube. My PE measured BP length was 8.75" but I think I have lost about a quarter inch of that the last year.

The tube is a 2" X 10" “gravel vac cleaner” for aquariums. I modified the tube to increase the length and the base diameter by applying a short 1" long piece of 2" diam PVC pipe over the end of the aquarium tube. Then I applied a 2" PVC coupling(2.375" ID.) To get more length and and larger base ID(my base diameter, I think, is about 2.2"). In effect, what I have is a two stage tube that will accommodate a 7.5" base girth for about 2" of length then 6.25" girth the remaining 9.25" of the tube and an overall length of 11.25". I will post pics of all the equipment later.

[fow1]

No comments? Is that good?

On to the next episode on balls.

My next PIC is of me pumping my balls. My ball tube is homemade from a jelly glass and a 2" piece of 2" PVC pipe. I tried to hot glue the PVC to the glass but it did not adhere to well so I wound up taping it on and works fine. I drilled a hole in the bottom of the glass and insert a piece of 1/4" vinyl tube. I am pumping and holding 3 to 5 inch vac. Am hoping to increase ball diameter(hopeful some permanent) and sac length. Presently packing the tube to 4.75" length and only have .5" left in tube. Will have to modify soon.

[Tekcon]

I'll comment...

I'm an advicate of people to buy professional pump equipment for their penis.

However, your ball pumping is a good idea... most pump sites encourage people to buy a Stage 2 cylinder, which in my opinon, leaves the penis looking very disfigured afterwords...

[fow1]

Tekon, thanks for the comment.

Head Pumping. This is my homemade head cup. It is fabricated from one of the planter peanut bubble glass caps and a PVC 1 ½" male plain to male threaded connector. Again, I taped this on since I could not get hot glue to adhere. I drilled for the vinyl tubing down the side of the PVC - this way the vinyl tube is recessed enough to keep the skin from being drawn into the tubing. I am pumping 2 to 8 inc vac and packing the cup. This is fine but am pulling more of the shaft in than I like. Would like to pack with just from the glans out. Will need to fab a spacer to go between the cup and the pubic bone so penis shaft can not be pulled in(this could act like a stretcher).

My goal is to develop a permanently large well defined mushroom head. So far I am getting it pumped up - just hope some of it becomes permanent

[fow1]

Equipment - The attached picture is of my equipment. The vacuum pump is from Auto Zone and cost about $25. The aquarium Gravel Vac Cleaner (penis tube) is from a pet shop and cost $9(adapted with PVC fittings to accommodate base girth and add length) The ball tube is a jelly glass adapted using a piece of 2" PVC pipe. The head cup is a planter peanut jar bubble cap adapted with 1 ½” PVC connector. If needed or wanted the flow valves are for aquarium use

[Rifor]

Hey Fow, I'd like to see the end results after using all the pumps, especially an end result of the head pump, it looks likme you really are packing that cup!

I'm thinking of starting pumping myself, but I have always been sceptical of it since i have read that they don't give permanent gains. But I might have read that on pay sites, and most of them wouldn't want me to use a pump instead of buying their routine info, so they could have been lying I guess.

Do you know how long it does take to see permanent gains, and are they big gains quite quickly (similar to me gaining 0.4 inches in 1 month) or does it take a long time, and do you need a lot of manual stretching to keep the gains coming?

[fow1]

I tried the homemade cup for a while but wasw to hard to maintain a vacumn without packing and when packed not achieveing any further hed expansion. Most of what I've read indicates a preference of wrapping/pumping. I will try to post an illustration. I think I had more luck with the modified uli's.

[fitdude]

Thanks, buddy, for the pics and discussion. I used to be a pumper (store bought) but after seeing what you've accomplished, I'm re-thinking the pumping thing.

[fow1]

Hey Fitdude,

Please do not misunderstand the pics above. I do not claim any gains accepted temporary from pumping. All my gains were made prior to taking up pumping by the conventional methods of jelqing and strteching. Attached is a pic of me before I started pumping.

[longer]

I am impressed that you pack the tube in just a few days. I am using the same size cylinder or I think its the same .Mine is 2'' by 9 ''. I can only get about 1/2 '' at the base of my penis to fill the cylinder. I guess im afraid of trying it to fast. Keep up sending the great pictures

[fow1]

Guess I missed your post back in May. Just now ran across it. I could Pack a 2" tube before I started Pumping. I'm not trying to increase girth except on the head. When the diameter is packed the vac pulls more on the head. If it takes, here is my latested.

[liironbiker]

how do you "pack" the tube?