Sizemeister
08-26-2001, 11:27 PM
This was posted by BiB, of course.
-------------------------------------------
There are many similar exercises being performed here.
Most involve grabbing at the base , trapping as much
blood as possible, and pulling forward, forcing it
toward the head
Bib's "Uli thing"
diagram
new address:
PE Glossary & FAQ (http://pefaq.thundersplace.com/bib)
I wrote about the Uli thing before. I thought it was
too dangerous for most to try, but then all PE has
some risk. So I'll tell you what it is. Be very
careful.
First, it is basically an adjustable solid @#%$ ring
(not elastic) that is placed below (toward the
body)the area you wish to stress. The thing is about 1
inch wide (covers one inch of the shaft). You wrap
with Thera or some other protection and put the thing
over the wrap. Tighten a little. Begin to get an
erection. You will not get nor do you need a full
blown erection. You adjust the thing so it cuts off
all return blood without hindering the incoming blood.
Therefore it creates tremendous pressure. Then you can
further tighen to cut off back flow and increase the
pressure some more. Also, you can grasp the thing and
pull a little creating even more pressure. Yep,
definitely dangerous.
There is not an easy way to describe how to make the
one I use, but this will probably work:
Go back to the HD guy and tell him you need a couple
inches of the tubing. ha ha. Make sure it is at least
1/4 inch thick.
Cut off a one inch ring. Bevel the edges. Cut the ring
straight across. Get a full erection and put the ring
around at the thickest part. Cut off part of the ring
to leave about a 3/4 inch gap.
Then take a band clamp (hose clamp)and cut it about 1
inch behind the female end. Then cut off about two
inches of the male end. Drill a couple holes through
the grooving of the male and female end of the clamp.
Position the female end on one end of the ring and
drill holes. Do the same for the male end only the
male end should hang over the other edge of the ring
by an inch or so. Attach the ends to the ring with #8
bolts. TA DA!
Now, from past experience, I am sure noone understands
what I have written above. So when I get some time, I
will draw some instructions and get Banshee to post
them.
Be careful, this is not for newbies.
-------------------------------------------
There are many similar exercises being performed here.
Most involve grabbing at the base , trapping as much
blood as possible, and pulling forward, forcing it
toward the head
Bib's "Uli thing"
diagram
new address:
PE Glossary & FAQ (http://pefaq.thundersplace.com/bib)
I wrote about the Uli thing before. I thought it was
too dangerous for most to try, but then all PE has
some risk. So I'll tell you what it is. Be very
careful.
First, it is basically an adjustable solid @#%$ ring
(not elastic) that is placed below (toward the
body)the area you wish to stress. The thing is about 1
inch wide (covers one inch of the shaft). You wrap
with Thera or some other protection and put the thing
over the wrap. Tighten a little. Begin to get an
erection. You will not get nor do you need a full
blown erection. You adjust the thing so it cuts off
all return blood without hindering the incoming blood.
Therefore it creates tremendous pressure. Then you can
further tighen to cut off back flow and increase the
pressure some more. Also, you can grasp the thing and
pull a little creating even more pressure. Yep,
definitely dangerous.
There is not an easy way to describe how to make the
one I use, but this will probably work:
Go back to the HD guy and tell him you need a couple
inches of the tubing. ha ha. Make sure it is at least
1/4 inch thick.
Cut off a one inch ring. Bevel the edges. Cut the ring
straight across. Get a full erection and put the ring
around at the thickest part. Cut off part of the ring
to leave about a 3/4 inch gap.
Then take a band clamp (hose clamp)and cut it about 1
inch behind the female end. Then cut off about two
inches of the male end. Drill a couple holes through
the grooving of the male and female end of the clamp.
Position the female end on one end of the ring and
drill holes. Do the same for the male end only the
male end should hang over the other edge of the ring
by an inch or so. Attach the ends to the ring with #8
bolts. TA DA!
Now, from past experience, I am sure noone understands
what I have written above. So when I get some time, I
will draw some instructions and get Banshee to post
them.
Be careful, this is not for newbies.